Drywall · Canada

FLHA for crown moulding installation

By SiteSortedBuilt from provincial OHS law and CCOHS guidance · How we write and check theseUpdated November 9, 2026

Provincial OHS law requires hazards to be assessed and controlled before work starts. A field level hazard assessment (FLHA) for crown moulding installation is done on site at the start of the shift and again whenever conditions change.

It lists the tasks, hazards and controls, and every worker signs on before starting and signs off at the end of the shift. The main hazards are falling from height, falling from a ladder, saw cuts and kickback and lifting and carrying heavy loads.

Make this FLHA now Word template PDF

FLHA example: crown moulding installation

This is a complete FLHA for crown moulding installation, with 4 job steps. Open it in the builder to add your site, crew and signatures, change anything, and download a PDF. Or download the free Word template below and fill it in by hand.

Field Level Hazard Assessment (FLHA)

Fit crown moulding · Drywall · Example

Document FLHA-001 · Rev 1

Job steps, hazards and controls

#	Job step	Hazards	Risk before	Controls	Risk after
1	Set up a platform ladder or trestles	Falling from a ladder Falling from height	Critical	Use a platform ladder, mobile scaffold or aerial work platform for longer jobs instead of a straight ladder. Substitution Use CSA Grade 1, 1A or 1AA ladders in good condition. Remove any damaged ladder from site. Engineering Set extension ladders at a 4 to 1 angle on firm, level ground, tied or footed, and reaching 1 metre above the landing. Engineering Use ladders only for short, light work. Do not carry heavy or awkward loads up a ladder. Administrative Keep three points of contact and your belt buckle between the side rails. Do not overreach. Administrative Do not stand on the top three rungs of an extension ladder or the top step of a stepladder. Administrative Check the ladder before each use: feet, rungs, side rails and locks. Administrative Wear non-slip safety boots with clean soles. PPE Do the work from the ground where you can, for example pre-assemble on the ground or use extension poles. Elimination Install guardrails or edge protection on all open edges before work starts. Engineering (guarding) Use a scaffold, mobile work platform or aerial work platform instead of working off a ladder. Engineering Where edge protection is not practical, use a fall restraint or fall arrest system on a rated anchor point. Engineering Fall protection plan in place where required. Workers trained in fall protection (Working at Heights training in Ontario). Administrative Have a rescue plan so a worker hanging in a harness can be brought down within minutes. Administrative Wear a full body harness with a shock-absorbing lanyard, clipped on at all times when using fall arrest. PPE	Medium
2	Cut mitres with a saw on a stand	Saw cuts and kickback General dust	High	Keep blade guards fitted and working, and use the riving knife on table saws. Engineering Use push sticks and clamps, and support long pieces so they do not pinch the blade. Engineering Use a sharp, undamaged blade made for the material. Administrative Stand to one side of the blade line, out of the kickback path. Administrative Let the blade stop fully before reaching in or putting the saw down. Administrative Wear safety glasses, hearing protection and close-fitting clothes. PPE Use low-dust products, such as dust-reduced or pre-mixed compounds. Substitution Seal off the work area with plastic sheeting in occupied buildings. Engineering (guarding) Use tools with dust extraction and a vacuum for clean up. Engineering Lightly mist the area with water to keep dust down, away from anything electrical. Engineering Never dry sweep or blow dust off with compressed air. Administrative Wear a dust mask and safety glasses. PPE	Medium
3	Apply adhesive and fix lengths, two people for long pieces	Lifting and carrying heavy loads Hazardous chemicals	High	Plan to avoid carrying: have materials delivered, and old items picked up, as close as possible to where they are used. Elimination Use lighter or smaller loads: order smaller bags and shorter lengths, and drain or break down old items before moving them. Substitution Use trolleys, pallet jacks, hoists, vacuum lifters or equipment instead of carrying by hand. Engineering Use a two-person lift for anything heavy, long or awkward. Plan the route first and clear it. Administrative Keep the load close, back straight and no twisting. Turn with your feet. Administrative Rotate tasks and take breaks on long lifting jobs. Administrative Wear gloves for grip and safety boots to protect your feet. PPE Choose the least harmful product that does the job, for example water-based instead of solvent-based. Substitution Use chemicals in well-ventilated areas, or use fans and extraction in closed rooms. Engineering Read the Safety Data Sheet (SDS) and WHMIS labels before use. Workers have WHMIS training. Administrative Keep chemicals in labelled containers. Never decant into drink bottles. Administrative Store chemicals away from heat, food and drink, and keep products that react with each other apart. Administrative Have eye wash and a spill kit nearby, and wash hands before eating. Administrative Wear chemical-resistant gloves and safety glasses or goggles as listed on the SDS. PPE Use a respirator with the right cartridge if the SDS calls for one. PPE	Medium
4	Fill and clean up	Poor housekeeping and waste	Medium	Order materials to size and send packaging back where you can. Elimination Put waste bins and chutes close to the work. Engineering Clean as you go, and do a full clean up at the end of each day. Administrative Keep exits, stairs and walkways clear at all times. Administrative Stack materials neatly on level ground, away from edges. Administrative Wear gloves when handling waste. PPE	Low

PPE

Safety glasses (CSA Z94.3)N95 respiratorCSA green triangle safety boots (CSA Z195)Hard hat (CSA Z94.1)Hearing protectionWork glovesChemical-resistant glovesSafety gogglesRespirator fit tested to CSA Z94.4 (P100 for dust, or the type the air test calls for)Coveralls

Plant and equipment

Mitre sawPlatform ladderNail gunHand tools

Emergency

Call 911. Add the nearest hospital, the muster point and the first aid attendant for your site.

Sign-off

Supervisor and every worker sign to confirm they have read and understood this FLHA, then sign off at the end of the shift.

Free FLHA template for crown moulding installation

Word (.docx) and PDF, Letter landscape, no email needed. Fill in your site details, then print or send it.

Word template (.docx)PDF template

Make yours in 2 minutes

Same document, filled in for your job. Answer a few yes or no questions, the crew signs on the phone, and you send the PDF.

Start this FLHA

Pre-start checklist for crown moulding installation

Tick these off before work starts. They come from the hazards, permits and equipment in this job.

FLHA read, explained and signed by everyone on the job
Guardrails or fall protection in place before anyone works at 3 m or more
Ladder inspected, secured and extending 1 m above the landing
First aid attendant, first aid kit and emergency number (911) confirmed
PPE checked and worn: safety glasses (CSA Z94.3), N95 respirator, CSA green triangle safety boots (CSA Z195), hard hat (CSA Z94.1)

The safe sequence of work

Set up a platform ladder or trestles
Cut mitres with a saw on a stand
Apply adhesive and fix lengths, two people for long pieces
Fill and clean up

Hazards to watch on crown moulding installation

The hazards most specific to this job, and the step where each one comes up.

Step 2Saw cuts and kickbackCircular saws, mitre saws and table saws cut fingers and hands or throw material back at the user.

Step 2General dustDust from drywall, joint compound, cement and clean up irritates eyes and lungs and makes it hard to see.

Step 3Hazardous chemicalsGlues, sealants, solvents, acids, cleaners and cement burn skin and eyes or cause breathing problems and poisoning.

Step 1Falling from a ladderThe ladder slips or tips, or the worker overreaches, and they fall onto a hard surface.

Step 1Falling from heightA worker falls from an edge, platform or opening and is badly hurt or killed. Fall protection is needed from 3 metres, and at any height over machinery, water or other hazards.

Step 3Lifting and carrying heavy loadsLifting, carrying, pushing or twisting with heavy or awkward loads strains the back, shoulders or knees.

Highest risk on crown moulding installation: Critical before controls (B), down to Medium after controls (A), on the Canada 5 by 5 risk matrix (likely and fatality becomes unlikely and serious injury).

What changes on your site

This example covers the job itself. Your site may add more. Add controls for any of these that apply (the builder asks you these as yes or no questions):

Could anyone fall 3 metres or more, or fall any distance into machinery, water, a hazardous substance or through an opening?
Will anyone work on a roof?
Is there a fragile roof, skylight or clear roof sheet?
Will you use a scaffold or mobile tower?
Will you use an aerial work platform (scissor lift or boom lift)?

Why FLHAs get rejected

Prime contractors and COR auditors send documents back for these reasons. This example avoids them, but check yours too.

End of shift boxes already say "None" when the form was signed at the start of the shift.
One FLHA reused for days or weeks, or a "review by" date a month away, when the work and conditions change daily.
No time of assessment and no record of any revision, which Alberta s.7(3) requires.
Workers signed that they "read" it, but nothing shows they took part, which Alberta s.8(1) requires.
Work at height with no fall protection plan where the province requires one, or no written rescue procedure for workers using fall arrest.
Permits or locates required on site but no permit or ticket numbers recorded.
No re-assessment entry after an obvious change such as weather, a new task or a new crew member.

Rules by province for crown moulding installation

Province or territory	Key local rule	Regulator
Ontario	Fall protection (O. Reg. 213/91 s.26) applies at a fall of more than 3 m, more than 1.2 m where the work area is used as a path for a wheelbarrow or similar equipment, and at any height into operating machinery, water or other liquid, a hazardous substance, or through an opening.	Ontario Ministry of Labour, Immigration, Training and Skills Development
British Columbia	Fall protection is required where a fall of 3 m or more may occur (s.11.2). A written fall protection plan is required at 7.5 m or more where there are no permanent guardrails (s.11.3).	WorkSafeBC
Alberta	A hazard assessment must be done before work begins, and before a new work site is built (OHS Code s.7(1)). The results must be written down with the controls (s.7(2)).	Alberta Occupational Health and Safety
Quebec	Guardrails (Safety Code s.2.9.1, as amended by Decret 63-2025) are needed where a worker could fall into liquid or a hazardous substance, onto moving parts or dangerous equipment, 1.2 m or more when using a vehicle, 1.5 m or more when handling a load, and more than 3 m in all other cases.	CNESST (Commission des normes, de l'equite, de la sante et de la securite du travail)
Manitoba	A prime contractor is required whenever more than one employer or self employed person works on the site at the same time (Act s.7).	Manitoba Workplace Safety and Health Branch
Saskatchewan	An occupational health committee is required at 10 or more workers of one employer (Act s.3-22).	Saskatchewan Ministry of Labour Relations and Workplace Safety, OHS Division
Nova Scotia	Workers must be trained in fall protection before using it or working in, supervising or planning work in a fall protection area, with a refresher at least every 3 years (WHSR s.21.19).	Nova Scotia Department of Labour, Skills and Immigration, Safety Branch (OHS)
New Brunswick	Fall protection is needed from 3 m above water or the nearest permanent safe level (Reg 91-191 s.49(1)(a)(i)).	WorkSafeNB
Newfoundland and Labrador	Give written notice to the minister before starting a construction project that will last 30 days or more, with the site, location, type of work and number of workers (Regs s.8).	Government Services, Occupational Health and Safety Division
Prince Edward Island	Fall protection is needed from 3 m above the nearest safe surface or water (Fall Protection Regulations s.2(1)(a)).	Workers Compensation Board of PEI, OHS Division
Yukon	Every employer must do hazard assessments with the committee, representative or workers, and redo them after significant changes or incidents (Regs s.1.03.01).	Yukon Workers' Safety and Compensation Board
Northwest Territories	Fall protection is needed from 3 m, or lower if there is a risk of injury (s.119(1)). Guardrails are needed for falls of 1.2 m to 3 m at permanent work sites (s.119(2)).	Workers' Safety and Compensation Commission (WSCC)
Nunavut	No 911. To reach the RCMP in an emergency, dial your community's first three digits then 1111 (Iqaluit: 979-1111). Put the local fire, ambulance and RCMP numbers on every FLHA.	Workers' Safety and Compensation Commission (WSCC)

Questions

Do I need an FLHA for crown moulding installation?

Who signs the FLHA?

The supervisor and every worker take part in the assessment and sign on before work starts, then sign off at the end of the shift. Review it and re-sign whenever the task or conditions change.

How long do I keep it?

Keep completed hazard assessments for at least 3 years (COR auditors sample the last 12 months). Review this FLHA and re-sign whenever the task, crew or conditions change.

What PPE is needed for crown moulding installation?

Usually Safety glasses (CSA Z94.3), N95 respirator, CSA green triangle safety boots (CSA Z195), Hard hat (CSA Z94.1), Hearing protection, Work gloves, Chemical-resistant gloves, Safety goggles, Respirator fit tested to CSA Z94.4 (P100 for dust, or the type the air test calls for), Coveralls. The site rules may add more, so check with the general contractor.

More drywall FLHAs

FLHADrywall Installation9 steps FLHADrywall Finishing5 steps FLHACeiling Installation5 steps FLHADrywall Repair5 steps FLHAStucco Application5 steps FLHASuspended Ceiling Installation4 steps

Related jobs in other trades

ScaffoldingScaffold ErectionAlso involves falling from height Excavation and earthworksTrenchingAlso involves falling from a ladder

Toolbox talks for this job

Toolbox talkLadder Safety Toolbox talkWHMIS and Hazardous Products Toolbox talkCrane and Lifting Safety

Blank FLHA template: free FLHA templates. Also for other countries: Australia (SWMS) · United Kingdom (RAMS) · United States (JHA)