Tiling · Canada

FLHA for bathroom tiling

By SiteSortedBuilt from provincial OHS law and CCOHS guidance · How we write and check theseUpdated November 9, 2026

Provincial OHS law requires hazards to be assessed and controlled before work starts. A field level hazard assessment (FLHA) for bathroom tiling is done on site at the start of the shift and again whenever conditions change.

It lists the tasks, hazards and controls, and every worker signs on before starting and signs off at the end of the shift. The main hazards are silica dust from concrete, brick, stone and tiles, saw cuts and kickback, loud noise and lifting and carrying heavy loads.

Make this FLHA now Word template PDF

FLHA example: bathroom tiling

This is a complete FLHA for bathroom tiling, with 5 job steps. Open it in the builder to add your site, crew and signatures, change anything, and download a PDF. Or download the free Word template below and fill it in by hand.

Field Level Hazard Assessment (FLHA)

Bathroom tiling · Tiling · Example

Document FLHA-001 · Rev 1

Job steps, hazards and controls

#	Job step	Hazards	Risk before	Controls	Risk after
1	Check waterproofing is done and cured	Hazardous chemicals	Medium	Choose the least harmful product that does the job, for example water-based instead of solvent-based. Substitution Use chemicals in well-ventilated areas, or use fans and extraction in closed rooms. Engineering Read the Safety Data Sheet (SDS) and WHMIS labels before use. Workers have WHMIS training. Administrative Keep chemicals in labelled containers. Never decant into drink bottles. Administrative Store chemicals away from heat, food and drink, and keep products that react with each other apart. Administrative Have eye wash and a spill kit nearby, and wash hands before eating. Administrative Wear chemical-resistant gloves and safety glasses or goggles as listed on the SDS. PPE Use a respirator with the right cartridge if the SDS calls for one. PPE	Medium
2	Mix adhesive with gloves, mask and paddle mixer	General dust Wet concrete and cement burns Injury from power tools	Medium	Use low-dust products, such as dust-reduced or pre-mixed compounds. Substitution Seal off the work area with plastic sheeting in occupied buildings. Engineering (guarding) Use tools with dust extraction and a vacuum for clean up. Engineering Lightly mist the area with water to keep dust down, away from anything electrical. Engineering Never dry sweep or blow dust off with compressed air. Administrative Use long-handled tools and pumps to cut down contact. Engineering Wash concrete off skin straight away with clean water. Administrative Have clean water and eye wash at the pour. Administrative Wear waterproof gloves, long sleeves and rubber boots with pants worn over the top. PPE Wear safety glasses or goggles to stop splashes. PPE Keep all guards fitted and working. Never tie back or remove a guard. Engineering Clamp or secure the work piece. Do not hold it by hand. Engineering Only trained, competent people use power tools, following the maker's instructions. Administrative Check tools before use. Unplug or remove the battery before changing blades or bits. Administrative No loose clothing, jewellery or long hair near spinning parts. Administrative	Medium
3	Cut tiles wet or outside, with extraction for dry cuts	Silica dust from concrete, brick, stone and tiles Saw cuts and kickback Loud noise	Critical	Order materials cut to size, or use low-dust methods such as score and snap or a block splitter. Substitution Cut outdoors or in a separate area, with other people well away and upwind. Engineering (guarding) Use water on the blade or on-tool dust extraction connected to a HEPA vacuum. Engineering Clean up with a vacuum or wet methods. Never dry sweep or use compressed air. Administrative Have a silica exposure control plan where your province requires one. Administrative Wear a fit-tested N95 (or better) respirator. PPE Keep blade guards fitted and working, and use the riving knife on table saws. Engineering Use push sticks and clamps, and support long pieces so they do not pinch the blade. Engineering Use a sharp, undamaged blade made for the material. Administrative Stand to one side of the blade line, out of the kickback path. Administrative Let the blade stop fully before reaching in or putting the saw down. Administrative Use quieter tools and methods, such as cut-to-size materials, low-noise machines and battery tools. Substitution Keep noisy equipment away from work areas, and use screens or distance between the noise and people. Engineering (guarding) Keep tools maintained and use mufflers on compressors and generators. Engineering Limit time on noisy tools and rotate workers. Administrative If you have to shout to be heard 1 metre away, wear hearing protection. Administrative	Medium
4	Lay tiles on knee pads, carrying large tiles with two people	Lifting and carrying heavy loads Repetitive work and awkward postures Cuts from sharp edges	High	Plan to avoid carrying: have materials delivered, and old items picked up, as close as possible to where they are used. Elimination Use lighter or smaller loads: order smaller bags and shorter lengths, and drain or break down old items before moving them. Substitution Use trolleys, pallet jacks, hoists, vacuum lifters or equipment instead of carrying by hand. Engineering Use a two-person lift for anything heavy, long or awkward. Plan the route first and clear it. Administrative Keep the load close, back straight and no twisting. Turn with your feet. Administrative Use tools that cut the effort: powered screwdrivers, long-handled tools and extension poles for overhead work. Substitution Set work up at waist height on benches or trestles where you can. Engineering Use light tools with good grips, and keep blades and bits sharp. Engineering Rotate tasks and take short breaks every hour on repetitive work. Administrative Warm up before heavy physical work and report aches and pains early. Administrative Deburr or cover sharp edges, and fit edge protectors on exposed sheet metal. Engineering Use knives with retractable or self-retracting blades. Engineering Cut away from your body and keep your other hand clear. Administrative Put used blades in a blade bin or sharps container. Administrative Use two people to handle large sheets of metal or glass. Administrative	Medium
5	Grout and clean, keeping floors dry	Slips and trips Hazardous chemicals	Medium	Plan walkways and keep them clear of materials, hoses and leads. Elimination Run leads and hoses overhead on hooks or stands, or along walls, not across walkways. Engineering Fill or cover holes, and lay boards or mats on muddy access paths. Engineering Clean up offcuts, packaging and spills as you go, not at the end of the day. Administrative Keep work areas, stairs and access paths well lit. Administrative Wear safety boots with good grip, laced up. PPE Hazardous chemicals: see step 1 for the full controls Administrative	Medium

PPE

Safety glasses (CSA Z94.3)N95 respiratorKnee padsChemical-resistant glovesHearing protectionCSA green triangle safety boots (CSA Z195)Safety gogglesRespirator fit tested to CSA Z94.4 (P100 for dust, or the type the air test calls for)CoverallsWork glovesCut-resistant gloves

Plant and equipment

Wet tile sawAngle grinderHand toolsPower drill

Emergency

Call 911. Add the nearest hospital, the muster point and the first aid attendant for your site.

Sign-off

Supervisor and every worker sign to confirm they have read and understood this FLHA, then sign off at the end of the shift.

Free FLHA template for bathroom tiling

Word (.docx) and PDF, Letter landscape, no email needed. Fill in your site details, then print or send it.

Word template (.docx)PDF template

Make yours in 2 minutes

Same document, filled in for your job. Answer a few yes or no questions, the crew signs on the phone, and you send the PDF.

Start this FLHA

Pre-start checklist for bathroom tiling

Tick these off before work starts. They come from the hazards, permits and equipment in this job.

FLHA read, explained and signed by everyone on the job
Water suppression or on-tool extraction fitted; respirators fit tested
First aid attendant, first aid kit and emergency number (911) confirmed
PPE checked and worn: safety glasses (CSA Z94.3), N95 respirator, knee pads, chemical-resistant gloves

The safe sequence of work

Check waterproofing is done and cured
Mix adhesive with gloves, mask and paddle mixer
Cut tiles wet or outside, with extraction for dry cuts
Lay tiles on knee pads, carrying large tiles with two people
Grout and clean, keeping floors dry

Hazards to watch on bathroom tiling

The hazards most specific to this job, and the step where each one comes up.

Step 2Wet concrete and cement burnsWet concrete, mortar and cement burn skin and eyes. Burns can be deep and are often not felt until later.

Step 3Saw cuts and kickbackCircular saws, mitre saws and table saws cut fingers and hands or throw material back at the user.

Step 2General dustDust from drywall, joint compound, cement and clean up irritates eyes and lungs and makes it hard to see.

Step 2Injury from power toolsDrills, saws, routers and sanders kick back, catch clothing or throw debris, causing cuts, broken bones and eye injuries.

Step 4Repetitive work and awkward posturesDoing the same movement for hours, kneeling or working overhead causes long-term damage to joints, muscles and tendons.

Step 1, 5Hazardous chemicalsGlues, sealants, solvents, acids, cleaners and cement burn skin and eyes or cause breathing problems and poisoning.

Highest risk on bathroom tiling: Critical before controls (B), down to Medium after controls (A), on the Canada 5 by 5 risk matrix (likely and fatality becomes unlikely and serious injury).

What changes on your site

This example covers the job itself. Your site may add more. Add controls for any of these that apply (the builder asks you these as yes or no questions):

Could anyone fall 3 metres or more, or fall any distance into machinery, water, a hazardous substance or through an opening?
Will anyone use a ladder or stepladder?
Will anyone work on a roof?
Is there a fragile roof, skylight or clear roof sheet?
Will you use a scaffold or mobile tower?

Why FLHAs get rejected

Prime contractors and COR auditors send documents back for these reasons. This example avoids them, but check yours too.

End of shift boxes already say "None" when the form was signed at the start of the shift.
One FLHA reused for days or weeks, or a "review by" date a month away, when the work and conditions change daily.
No time of assessment and no record of any revision, which Alberta s.7(3) requires.
Workers signed that they "read" it, but nothing shows they took part, which Alberta s.8(1) requires.
Work at height with no fall protection plan where the province requires one, or no written rescue procedure for workers using fall arrest.
Permits or locates required on site but no permit or ticket numbers recorded.
No re-assessment entry after an obvious change such as weather, a new task or a new crew member.

Rules by province for bathroom tiling

Province or territory	Key local rule	Regulator
Ontario	Fall protection (O. Reg. 213/91 s.26) applies at a fall of more than 3 m, more than 1.2 m where the work area is used as a path for a wheelbarrow or similar equipment, and at any height into operating machinery, water or other liquid, a hazardous substance, or through an opening.	Ontario Ministry of Labour, Immigration, Training and Skills Development
British Columbia	Fall protection is required where a fall of 3 m or more may occur (s.11.2). A written fall protection plan is required at 7.5 m or more where there are no permanent guardrails (s.11.3).	WorkSafeBC
Alberta	A hazard assessment must be done before work begins, and before a new work site is built (OHS Code s.7(1)). The results must be written down with the controls (s.7(2)).	Alberta Occupational Health and Safety
Quebec	Guardrails (Safety Code s.2.9.1, as amended by Decret 63-2025) are needed where a worker could fall into liquid or a hazardous substance, onto moving parts or dangerous equipment, 1.2 m or more when using a vehicle, 1.5 m or more when handling a load, and more than 3 m in all other cases.	CNESST (Commission des normes, de l'equite, de la sante et de la securite du travail)
Manitoba	A prime contractor is required whenever more than one employer or self employed person works on the site at the same time (Act s.7).	Manitoba Workplace Safety and Health Branch
Saskatchewan	An occupational health committee is required at 10 or more workers of one employer (Act s.3-22).	Saskatchewan Ministry of Labour Relations and Workplace Safety, OHS Division
Nova Scotia	Workers must be trained in fall protection before using it or working in, supervising or planning work in a fall protection area, with a refresher at least every 3 years (WHSR s.21.19).	Nova Scotia Department of Labour, Skills and Immigration, Safety Branch (OHS)
New Brunswick	Fall protection is needed from 3 m above water or the nearest permanent safe level (Reg 91-191 s.49(1)(a)(i)).	WorkSafeNB
Newfoundland and Labrador	Give written notice to the minister before starting a construction project that will last 30 days or more, with the site, location, type of work and number of workers (Regs s.8).	Government Services, Occupational Health and Safety Division
Prince Edward Island	Fall protection is needed from 3 m above the nearest safe surface or water (Fall Protection Regulations s.2(1)(a)).	Workers Compensation Board of PEI, OHS Division
Yukon	Every employer must do hazard assessments with the committee, representative or workers, and redo them after significant changes or incidents (Regs s.1.03.01).	Yukon Workers' Safety and Compensation Board
Northwest Territories	Fall protection is needed from 3 m, or lower if there is a risk of injury (s.119(1)). Guardrails are needed for falls of 1.2 m to 3 m at permanent work sites (s.119(2)).	Workers' Safety and Compensation Commission (WSCC)
Nunavut	No 911. To reach the RCMP in an emergency, dial your community's first three digits then 1111 (Iqaluit: 979-1111). Put the local fire, ambulance and RCMP numbers on every FLHA.	Workers' Safety and Compensation Commission (WSCC)

Questions

Do I need an FLHA for bathroom tiling?

Who signs the FLHA?

The supervisor and every worker take part in the assessment and sign on before work starts, then sign off at the end of the shift. Review it and re-sign whenever the task or conditions change.

How long do I keep it?

Keep completed hazard assessments for at least 3 years (COR auditors sample the last 12 months). Review this FLHA and re-sign whenever the task, crew or conditions change.

What PPE is needed for bathroom tiling?

Usually Safety glasses (CSA Z94.3), N95 respirator, Knee pads, Chemical-resistant gloves, Hearing protection, CSA green triangle safety boots (CSA Z195), Safety goggles, Respirator fit tested to CSA Z94.4 (P100 for dust, or the type the air test calls for), Coveralls, Work gloves, Cut-resistant gloves. The site rules may add more, so check with the general contractor.

More tiling FLHAs

FLHAFloor Tiling5 steps FLHAWaterproofing9 steps FLHASplashback Tiling4 steps FLHATile Removal9 steps FLHABalcony Tiling5 steps

Related jobs in other trades

Excavation and earthworksTrenchingAlso involves loud noise

Toolbox talks for this job

Toolbox talkOverhead Power Lines Toolbox talkExtension Leads and Power Tools Toolbox talkSilica Dust Toolbox talkHearing Protection and Noise

Blank FLHA template: free FLHA templates. Also for other countries: Australia (SWMS) · United Kingdom (RAMS) · United States (JHA)